Skip to content
DCC Sniffer. Pour les locos, impeccable.
The one I liked best is the All are free software (iTrain is free with limitations, 3 types of licences are available fom €79,- onwards)Very many thanks for your fantastic site – you projects are really useful and very well explained.Pete, I’m sorry but I don’t have the time for that at the moment … too busy with all kinds of other stuff. An Arduino library for creating NMRA DCC decoding devices. A while back I started to experiment with reading a DCC signal into a microprocessor. However ... they are shown as numbers, which makes it rather difficult to understand what is what. I wanted to try the TRCT5000. libraries/DCC_Decoder/DCC_Decoder.cpp (the library implementation file) See the (Sep 2014) ECoS firmware 4 has a VNC server built in, which makes it possible to not only show the ECoS screen on your PC or tablet, but also to operate it! I took that, added the LCD library and played around with displaying it to a 4x20 character LCD. Megapoints Controllers 28,344 ... Arduino using DCC Commands to Operate a Servo - …
They show the DCC packets that are detected.
User manual desrcibing the needed hardware and how to configure the software is included.The main loop scans all 16 inputs and stores the state in a 16 bit integer called ‘sensors’. libraries/DCC_Decoder/readme.txt (this file)After this library is installed, you just have to start the Arduino application.To use this library in a sketch, go to the Sketch | Import Library menu and
Mit dieser Hardware kann der Arduino das DCC-Signal dekodieren. The best advice I can give is to download TC and try it.Yes, the PC software can be used to switch the relays, via a DCC decoder, for which I would use DCCNext (www.arcomora.com) which set you back just €7,50 for 16 DCC controlled outputs.What helped with me to suppress flickering is to connect all unused inputs to GND and particularly pin 12 of the final Arduino in the chain. An Arduino library for creating NMRA DCC decoding devices. See DCC Plus Plus article . The first one in the chain has data out pin 13 connected to S88.For the sensors anything can be used that pulls an Arduino input to GND, like a reed switch or an optical detector. Arduino Products. Uses Arduino 1.6 IDE.To install this library, just place this entire folder as a subfolder in your
It’s the input where the next Arduino should be connected to, but if it is the final in the chain there is no next. The DCC++ Base Station consists of an Arduino micro controller fitted with an Arduino Motor Shield that can be connected directly to the tracks of a model railroad. DCC++. They show the DCC packets that are detected.
Both contain example code that lets them work as a DCC monitor. Unfortunatelly to comunicate from Arduino to DFPlayer I need to use serial comunication ( SoftwareSerial.h ), but these libraries are in conflict with the DCC libraries ( DCC_Decoder.h ) and dosn’t work! After sending each bit it reads the data-in, to which the data-out of the next Arduino in the chain is connected.
This will add a corresponding line to the top of your sketch:To stop using this library, delete that line from your sketch. I seen your RB_DDC_Decoder_Sound, but I want create a Decoder Sound function without PC!I’d get a second Arduino to connect the MP3 player to. NEU: Zusätzlicher DCC-Ausgang ohne Abschaltung bei Power-OFF für S88 oder LocoNet Lauffähig auf ESP8266 und Arduino DUE Korrektur der Datenverarbeitung bei Zubehörbefehlen Korrektur bei der Ausgabe des IDLE-Packets DCC Interface Dokumentation.
Use Git or checkout with SVN using the web URL.
The system consists of a DCC++ Base Station and DCC++ Controller. I enjoy more the electronic side of dcc than running a layout The youtube description shows a link to a dropbox for all the source code including yours.Thanks for all Arduino projects again!
libraries/DCC_Decoder/keywords.txt (the syntax coloring file) DCC Occupancy Detector Revised 0 2-24-2016. The majority are optimized for DCC and few systems claim to work in DC. J'ai uploadé ce sniffer sur un Arduino, et à priori ça fonctionne, testé avec la petite centrale noire Fleischmann fournie avec la Multimaus (la centrale basique, pas la Z21). Post by RudyB » Fri Oct 23, 2015 6:39 pm . I have an issue about how can create a DCC Decoder Function with sound effects, using a little mp3 player ( DF Player mini mp3). The DCC Arduino can send digital outputs, connected to the MP3 Arduino’s inputs to determine which sound to play.I have only done multiple locs in a block with TC but only with 2 locs.